to be updatedRun measure_mask_steps_full
Lenslet mask stuck at Scan 2 but the script continued. No light. ctr + c to abort the script.
Multiple RPC errors.
Error stepping motor.
| Code Block |
|---|
124] osrseng@napili: ./measure_mask_steps_full Mask slide is ok. setting lock = 1 (wait) setting lock = 1 (wait) setting lock = 1 (wait) osirisAutoRamp: Frame read time is 1.4752800 seconds. setting itime = 4000 (wait) osirisAutoRamp: spec itime set to 4000 ms. setting sampmode = 3 (wait) osirisAutoRamp: Sampling mode set to MCDS. setting numreads = 2 (wait) osirisAutoRamp: reads set to 2 setting coadds = 1 (wait) setting setnum = 10 (wait) setting framenum = 0 (wait) setting comment = darks (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ............ setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ............ rpc_clientOpen: clnt_create failed localhost, 1868983411 clnt_call: RPC: Program not registered rpcKey_clientFuncs.c, 3943: failed to connect to RPC server localhost,ofls (1868983411 v1) rpcKey_clientFuncs.c, 3946: Error: failed to create RPC client handle. ERROR - Failed to create RPC client handle for client ofls. Sorry, the modify command was not able to contact the control system: ERROR - Failed to create RPC client handle for client ofls. Lamp warming for 300 seconds setting pos = 1 (wait) Waiting for mask motion to complete...: (Time estimate = 180 sec.) setting step = -47 (wait) OMS Error (13): Error stepping motor. because Error setting step: ERROR - OMS Error (13): Error stepping motor. because This scan will likely take 238 minutes to complete setting comment = om4s location=-4702 (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting step = 10 (wait) setting comment = om4s location=-5329 (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ............ setting step = 10 (wait) setting comment = om4s location=-5319 (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting step = 10 (wait) setting comment = om4s location=-5310 (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting step = 10 (wait) setting comment = om4s location=-5299 (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting step = 10 (wait) setting comment = om4s location=-5289 (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ........... setting step = 10 (wait) setting comment = om4s location=-5279 (wait) setting go = 1 (wait) Waiting for exposure to end: (Time estimate = 8040 sec.) ...........^CControl C abort detected ... Ending wf_sgo. Control C abort detected ... Ending ./measure_mask_steps_full. setting lock = 0 (wait) setting lock = 0 (wait) setting lock = 0 (wait) setting lock = 0 (wait) rpc_clientOpen: clnt_create failed localhost, 1868983411 clnt_call: RPC: Program not registered rpcKey_clientFuncs.c, 3943: failed to connect to RPC server localhost,ofls (1868983411 v1) rpcKey_clientFuncs.c, 3946: Error: failed to create RPC client handle. ERROR - Failed to create RPC client handle for client ofls. Sorry, the modify command was not able to contact the control system: ERROR - Failed to create RPC client handle for client ofls. |