200614 scans

Run measure_mask_steps_full
Lenslet mask stuck at Scan 2 but the script continued. No light. ctr + c to abort the script.
Multiple RPC errors.
Error stepping motor.
124] osrseng@napili: ./measure_mask_steps_full 
Mask slide is ok.
setting lock = 1 (wait)
setting lock = 1 (wait)
setting lock = 1 (wait)
osirisAutoRamp: Frame read time is 1.4752800 seconds.
setting itime = 4000 (wait)
osirisAutoRamp: spec itime set to 4000 ms.
setting sampmode = 3 (wait)
osirisAutoRamp: Sampling mode set to MCDS.
setting numreads = 2 (wait)
osirisAutoRamp: reads set to 2
setting coadds = 1 (wait)
setting setnum = 10 (wait)
setting framenum = 0 (wait)
setting comment = darks (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
............
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
............
rpc_clientOpen: clnt_create failed localhost, 1868983411
clnt_call: RPC: Program not registered
rpcKey_clientFuncs.c, 3943: failed to connect to RPC server localhost,ofls (1868983411 v1)
rpcKey_clientFuncs.c, 3946: Error: failed to create RPC client handle.
ERROR - Failed to create RPC client handle for client ofls.
Sorry, the modify command was not able to contact the
control system: ERROR - Failed to create RPC client handle for client ofls.
Lamp warming for 300 seconds
setting pos = 1 (wait)
Waiting for mask motion to complete...:
(Time estimate = 180 sec.)

setting step = -47 (wait)
OMS Error (13): Error stepping motor. because  
Error setting step: ERROR - OMS Error (13): Error stepping motor. because  
This scan will likely take 238 minutes to complete
setting comment = om4s location=-4702 (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting step = 10 (wait)
setting comment = om4s location=-5329 (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
............
setting step = 10 (wait)
setting comment = om4s location=-5319 (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting step = 10 (wait)
setting comment = om4s location=-5310 (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting step = 10 (wait)
setting comment = om4s location=-5299 (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting step = 10 (wait)
setting comment = om4s location=-5289 (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........
setting step = 10 (wait)
setting comment = om4s location=-5279 (wait)
setting go = 1 (wait)
Waiting for exposure to end:
(Time estimate = 8040 sec.)
...........^CControl C abort detected ... Ending wf_sgo.
Control C abort detected ... Ending ./measure_mask_steps_full.
setting lock = 0 (wait)
setting lock = 0 (wait)
setting lock = 0 (wait)
setting lock = 0 (wait)
rpc_clientOpen: clnt_create failed localhost, 1868983411
clnt_call: RPC: Program not registered
rpcKey_clientFuncs.c, 3943: failed to connect to RPC server localhost,ofls (1868983411 v1)
rpcKey_clientFuncs.c, 3946: Error: failed to create RPC client handle.
ERROR - Failed to create RPC client handle for client ofls.
Sorry, the modify command was not able to contact the
control system: ERROR - Failed to create RPC client handle for client ofls.
Staff Astronomers

200614 scans

Analytics

Related content
